วันอังคารที่ 17 พฤษภาคม พ.ศ. 2554

The DIY Way To sharpen blades Prato

The DIY Way To sharpen blades Prato

The DIY Way To sharpen blades Prato

Posted: 17 May 2011 04:00 AM PDT

Is your lawn mower tearing of the grass of the lawn, instead of cutting it? Your lawn looked like it was eaten by a goat, despite cutting the lawn? Wait, do not pull the hair from the root. Help is at hand. We'll show you how to sharpen the blades at a minimum price and effort.

Your manual lawn mower – walk behind the Faithful

Tools: The tools you need for this occupation are

You and your level of about 2 hours orless

A bastard file of about 12 cm in length

A small crow bar to prevent movement of the mower rotor.

A work table is useful to work comfortably dong.

Action: You can use the next procedure for guidance and to make changes to suit you. Remember, the process is not sacrosanct. The results are important, not the process.

If possible, remove the lawn mowers and place to deal on the table.

Of course, in parentheses, if possible.If you are not a terminal, do not bother to ensure against any block, so that the limited movement away from you.

Fix the crowbar in the wings, so that will not turn on

With the help of the bastard file, file the edges of the leaves, allowing it to focus. Working at an angle of 45 degrees

If the blade is sharpened, remove the crowbar and turn the rotor to work on another sheet. Repeat the process until all the leaves are sharp.

If you have a flexible shaftMill in your DIY workshop, you will be able to complete its work by 5 or 10 minutes per sheet. Make a model of blade profile before your work is often compared. This is necessary to ensure that no cut in one place.

Safety Tips for you

While sharpening the blades ensure that the bar is not too long or you risk being hurt.

The blades of the mower Power

Depending on the mower the procedure may vary.We have included general statements in this procedure, you should have the procedure change. Keep the mower maintenance manual on hand if you have one.

Tools required.

Siphon hose and clean container

heavy work gloves and safety glasses

Double-cut (medium rough) flat file

Waste timber

September wrench

Rubber mallet *

Vise or C clamps

Rotary blade sharpener accessory

* Electric drill

Screwdriver or 1/4-inch. Rod orPin *

Blade Balancer

Replacement blade *

* Only if necessary

The list may seem terrible, but the tools are generally associated with all DIY enthusiasts.

Procedure:

The procedure is given for the lawn mower simple single blade, but the same is true for all types of blades, whether single or double room

Wear gloves and clean the motor and the gasoline tank from outside

Remove the spark plug from the engine

Remove all fuel from tankGasoline engine. Use the hose, so do not pour gasoline on the floor.

Completely drain the oil from the gearbox, if you have a

Turn the engine and have access to the blade.

Disconnect the motor does not move well and thoroughly clean the knife

Remove with the help of a socket wrench, remove the nut holding the blade. Usually the mother will be released in the opposite direction of rotation. They can intervene to stop the screwdriver into the fan motorMotor rotation.

If you find it too hard to unlock the nut, remove one or two drops of rust to create chemical and try after 30 minutes

After removing the blade, clamp in a vice and sharpen with a file or a grinder. Sharpen only the outer 2 to 3 inches. The area is sharpened to know when you see the knife.

Sharpen only to the extent necessary. Too much heat is required. This is not the knife. It works forThe motor speed

After grinding with the thumb. Make sure your thumb cut. If you have sharpening done before, or seen someone do it, you'll know what we mean.

Balance the blade with a small balancing tool on VEE blocks or even on two foot rulers side by side

Put the filling knife, motor oil and gasoline and test the sharpness of the blades on an integral part of your lawn

Safety Tips:

Always use safetygoggles and gloves when working with power tools.

Be sure to remove the spark plug first. Serious accidents can happen if you do not.

เขียนโดย ที่

ไม่มีความคิดเห็น:

แสดงความคิดเห็น

สมัครสมาชิก: ส่งความคิดเห็น (Atom)